ENERGETICAL THEORY OF METAL PROCESSING AS THE BASIS OF THE CALCULATING RESOURCE-SAVING SEQUENCES METHOD OF WIRE-DRAWING
DOI:
https://doi.org/10.14529/met200108Keywords:
wire drawing, monolithic drawing die, working half-angle of wire drawing, elementary degree of deformation, coefficient of frictionAbstract
The calculation formulas for determining the power spent on the process of wire drawing in a monolithic die based on the energy method for solving technological problems of metal forming are obtained in this article. The founder of this method is V.N. Vydrin. The power of electric energy was converted by an electric motor into mechanical energy and supplied to the block of a drawing mill by reducer. It is spent on overcoming the friction forces in a monolithic drawing die and on the shape change of metal during drawing.
The article provides a methodology for calculating the energy efficiency of the wire drawing process. It is established that an increase in mechanical properties can lead to a decrease in the unhomogeneity of deformation over its cross section. It has been determined that for the formation of mechanical properties and the retention of the ductility margin of the wire, the drawing sequence must be constructed with the maximum degrees of deformation that are maximum permissible under the condition of continuous drawing, the minimum angle of die, and ensuring a low coefficient of friction. It is necessary to be guided not only by the quality criterion of the wire, characterized by the level of mechanical properties, but also by the energy efficiency of the process, for constructing resource-saving drawing sequences. The calculation of the power spent on shaping and overcoming the friction forces in the deformation zone showed that the efficiency of the drawing process increases with an increase in an elementary degree of deformation, a decrease in the working angle of the die and the value of the friction coefficient. The analysis of a typical drawing sequence from the point of view of these principles revealed that the resource-saving effect is achieved when using monolithic dies with a working angle of 8°. In this case, the route should be consistent with the remaining parameters of the deformation zone (an elementary degree of deformation and a coefficient of friction provided by the quality of preparation of the surface of the workpiece and the applied process lubricant).
References
Vydrin V.N. Dinamika prokatnykh stanov [The dynamics of rolling mills]. Sverdlovsk, Metallurgizdat Publ., 1960. 256 p.
Kharitonov V.A., Zyuzin V.I., Belan A.K. Resursosberezheniye pri proizvodstve provoloki [Resource conservation in wire production]. Magnitogorsk, MSTU Publ., 2003. 194 p.
Krasilnikov L.A., Lysenko A.G. Volochil’shchik provoloki: ucheb. posobiye [Wire Drawer]. Moscow, Metallurgiya Publ., 1987. 320 p.
Perlin I.L., Yermanok M.Z. Teoriya volocheniya [Theory of drawing]. 2nd ed. Moscow, Metallurgiya Publ., 1971. 448 p.
Kulesha V.A., Klekovkina N.A., Belalov H.N. et al. Izgotovleniye vysokokachestvennykh metizov [Production of high-quality hardware]. Beloretsk, 1999. 328 p.
Rudskoy A.I., Lunev V.A., Shaboldo O.P. Volocheniye: ucheb. posobiye [Drawing]. St. Petersburg, Polytechnic University Publ., 2011. 126 p.
Radionova L.V., Ivanov V.A., Shatalov V.S. [Investigation of the influence of the working angle of a monolithic die on the stress-strain state of a wire in a deformation zone]. Engineering: a network electronic scientific journal, 2014, no. 2, pp. 21–25. (in Russ.)
Guryanov G.N. [The method of calculating the optimal angle of the working cone of the die when drawing a round solid profile]. Metallurgical and Mining Industry, 2010, no. 6, pp. 58–60. (in Russ.)
Lin J., Liu Y., Farrugia D. et al. Development of dislocation based-unified material model for simulating microstructure evolution in multipass hot rolling. Philosophical Magazine, 2005, vol. 85, no. 18, pp. 1967–1987. DOI: 10.1080/14786430412331305285
Kharitonov V.A., Radionova L.V. Proyektirovaniye resursosberegayushchikh tekhnologiy proizvodstva vysokoprochnoy uglerodistoy provoloki na osnove modelirovaniya: monogr. [Designing resource-saving technologies for the production of high-strength carbon wire based on modeling: monograph]. Magnitogorsk, MSTU Publ., 2008. 171 p.
Kolmogorov V.L. Mekhanika obrabotki metallov davleniyem [Mechanics of metal forming]. Moscow, Metallurgiya Publ., 1986. 689 p.
Rubio E.M., Camacho A.M., Sevilla L., Sebastián M.A. Calculation of the forward tension in drawing processes. J. Mater. Process. Technol. A, 2005, vol. 162–163, pp. 551–557. DOI: 10.1016/j.jmatprotec.2005.02.122
Dobrov I.V. [The development of the energy method for calculating the power parameters of the process of strip drawing in a monolithic fiber]. Proceedings of Universities. Non-Ferrous Metallurgy. 2016, no. 4, pp. 58–66. (in Russ.)
Radionov A.A., Radionova L.V. [The energy approach to the study of the effect of countertension on the process of drawing]. Proceedings of Universities. Ferrous Metallurgy, 2008, no. 5, pp. 19–22. (in Russ.)
Gun G.Ya. Teoreticheskiye osnovy obrabotki metallov davleniyem (teoriya plastichnosti) [Theoretical foundations of metal forming (plasticity theory)]. Moscow, Metallurgiya Publ., 1980. 456 p.
Radionova L.V. [Analytical studies of the influence of technological parameters on the strain rate during high-speed wire drawing]. Engineering: network electronic scientific journal, 2014, no. 1, pp. 28–33. (in Russ.)
Zaydes S.A. Ostatochnyye napryazheniya i kachestvo kalibrovannogo metalla [Residual stresses and quality of calibrated metal]. Irkutsk, Irkut. University Publ., 1992. 200 p.
Vishnyakov Y.D., Piskarev V.D. Upravleniye ostatochnymi napryazheniyami v metallakh i splavakh [Control of residual stresses in metals and alloys]. Moscow, Metallurgiya Publ., 1989. 254 p.
Kharitonov B.A., Radionova L.V. Proyektirovaniye resursosberegayushchikh tekhnologiy proizvodstva vysokoprochnoy uglerodistoy provoloki na osnove modelirovaniya [Designing resourcesaving technologies for the production of high-strength carbon wire based on modeling]. Magnitogorsk, MSTU Publ., 2008. 171 p.
Baron A.A., Gavlich D.S., Bahracheva Yu.S. [Specific energy of plastic deformation as a measure of crack resistance of structural materials]. Metals, 2003, no. 6, pp. 85–90. (in Russ.)
Kharitonov V.A., Radionova L.V., Safonov E.V. [Method for the production of high-strength wire with increased plastic properties of carbon steel]. Modeling and development of metal forming processes: interuniversity proceedings. Magnitogorsk, MSTU Publ., 2002, pp. 41–45. (in Russ.)
Radionova L.V., Kharitonov V.A., Zyuzin V.I., Rol'shchikov L.D. New technological lubricants for steel wire drawing. Steel in Translation, 2001, no. 12, pp. 49–50.
Kharitonov V.A., Zyuzin V.I., Radionova L.V., Rolshchikov L.D. [New technological lubricants and power parameters for drawing steel wire]. Bulletin “Ferrous metallurgy”, 2001, no. 10, pp. 38–39. (in Russ.)
Muskalski Z., Wiewiórowska S. The theoretical analysis of wire drawing process or hydrodynamic friction conditions. Metallurgical and Mining Industry, 2011, vol. 3, no. 7, pp. 74–78.
