Порошковые проволоки Fe–Cr–Al для дуговой металлизации жаростойких покрытий

Yu. S. Korobov; M. A. Filippov; A. S. Tabatchikov; S. V. Nevezhin; V. S. Verkhorubov; G. A. Rimer

Authors

Yu. S. Korobov Ural Federal University named after the first President of Russia B.N. Yeltsin
M. A. Filippov Ural Federal University named after the first President of Russia B.N. Yeltsin
A. S. Tabatchikov Ural Federal University named after the first President of Russia B.N. Yeltsin
S. V. Nevezhin Ural Federal University named after the first President of Russia B.N. Yeltsin
V. S. Verkhorubov Ural Federal University named after the first President of Russia B.N. Yeltsin
G. A. Rimer Ural Federal University named after the first President of Russia B.N. Yeltsin

Keywords:

charge, alloying system, arc spraying, heat-resistance coatings, core wire, adhesion, porosity of coatings

Abstract

To monitor the homogeneity of powered wires the angle of repose and its coefficient of flow ability were defined. It has been established that a burden of special composition obtained by limiting the amount of coarse and fine fractions in comparison with the standard burden having initial granulation has a smaller angle of repose and higher flow ability, providing uniformity in particle size and chemical composition and improving coating quality. The influence of additional alloy building of wires with titanium, silicon and yttrium on heat resistance was studied by thermogravimetric analysis and scanning electron microscopy. It was defined that the introduction of titanium and silicon prevents the formation of carbide (Fe, Cr)₇C₃, aluminum nitride AlN and high temperature corrosion for both base alloy Fe-Cr-Al and for spraying coatings and the introduction of yttrium prevents the segregation of sulfur at the border due to the formation of sulfides Y₂S₃. For spraying coatings the same effects are achieved by the introduction of the wires of high amounts of titanium and silicon into the burden, which is associated with the conditions of their formation in arc spraying. On the basis of the established principles the powered wires of alloying system Fe-Cr-Al-Ti-Si were developed to be used as spraying coatings. Spraying coatings developed have the heat resistance equal to that of austenitic steels and much higher than that of ferrite-pearlite, ferrite-martensite steels that are widely used in boiler construction.

References

Iron-based coatings arc-sprayed with cored wires for applications at elevated temperatures / B. Wielage, H. Pokhmurska, M. Student et al. // Surface Coatings Technology. – 2013. – 220. – P. 27–35.

Lai, G.Y. High-Temperature Corrosion and Materials Applications / G.Y. Lai. – ASM International, 2007. – 461 p.

Жуков, Л.Л. Сплавы для нагревателей / Л.Л. Жуков. – М.: Металлургия, 1985. –144 с.

Sigler, D.R. Aluminum Oxide Adherence on Fe–Cr–A1 Alloys Modified with Group IIIB, IVB, VB, and VIB Elements / D.R. Sigler // Oxidation of Metals. – 1989. – 32. – pp. 337–355.

Modeling a formation of Fe–Cr–Al coating produced by arc spraying / Yu. Korobov, M. Filipov, M. Shallimov, S. Nevezhin // ITSC 2011. ASM International. – 2011. – P. 1463–1466.

Шалимов, М.П. Влияние гранулометрического состава компонентов на сыпучесть шихты порошковой проволоки / М.П. Шалимов, П.А. Табатчиков // Сварка и Диагностика. – 2012. –№ 5 – С. 45–48.

Никитин, В.И. Расчёт жаростойкости металлов / В.И. Никитин. – М.: Металлургия, 1976. – 207 с.

David, J.Y. High Temperature Oxidation and Corrosion of Metals / J.Y. David. – Netherlands: Elsevier, 2008. – 574 p.