Evaluation of deformations in corrosion thinwalled pipes at cold bending with rolling
Keywords:
deformation evaluation, thinwalled pipes, pipe bending, special machine, net methodAbstract
Corrosion-resistant thinwalled pipes are widely applied in aviation, rocket engineering, space engineering, ship building, mechanical engineering, iron&steel and non-ferrous industry, atomic energy, chemical, oil and gas industries and other areas. Pipe bending is one of the key operations of the technological procedure for pipeline part manufacture. Despite this fact, under modern production conditions it is virtually impossible to perform high-quality bending in the cold condition of pipes having the diameters larger than 60–70 mm as it is followed by the phenomena which are undesirable for the further operation: wall thinning on the pipe external side, elongation (flattening) of a cross-section, corrugation and fracture occurrence on the inside of a pipe.
The technology for thinwalled pipe bending developed by SUSU eliminates the above-mentioned drawbacks. At the rotation of a burnisher put into a pipe with quite a hard pull, at each point of a rolling annular area an alternating bending occurs when bending stresses reach the yield stress for a short time. Thus, at the application of a relatively small bending strain a moving rolling annular area bends. The article considers the results of the experimental evaluation of deformations in thinwalled pipes at bending with rolling. The authors provide the procedure for the experiment conduct. To conduct experiments, they used a special machine for pipe cold bending with rolling. The method of deformation evaluation is based on the “Net method”. The authors determined the elongation and shortening values for pipe walls involved in bending. The conducted research allowed for the evaluation of the deformation extent and nature in longitudinal and transverse sections of the pipe walls at bending with rolling and, as a result, the authors managed to calculate the specified deformations and pipe wall thinning which is an important operation characteristics.
References
Kozlov A.V., Bobylev A.V. Tekhnologiya i oborudovanie kholodnoi gibki tonkostennykh trub [Technology and Equipment for Thinwalled Pipe Cold Bending]. Chelyabinsk, South Ural St. Univ. Publ., 2007. 169 p.
Kozlov A.V., Sherkunov V.G. [Influence of Cold Bending with Rolling on Bending Pipe Wall Thickness]. Bulletin of Nosov Magnitogorsk State Technical University (MGTU), 2009, no. 3, pp. 32–34. (in Russ.)
Kozlov A.V., Sherkunov V.G. [Computer Simulation of Pipe Bending with Rolling]. Bulletin of TGU, 2009, pp. 11–15. (in Russ.)
Kulagin V.A., Sokolov N.Yu. [Improving the of Thermophysical Characteristics of Heat Pipes].
J. Sib. Fed. Univ. Eng. technol., 2017, vol. 10, no. 3, рр. 372–376. (in Russ.) DOI: 10.17516/1999-494X-2017-10-3-372-376
Lipovka Y.L., Belilovets V.I. [Some Theoretical Sides of Calculation of Temperature Deformations of Underground Heat Conductors]. J. Sib. Fed. Univ. Eng. technol., 2016, vol. 9, no. 4, рр. 546–562.
(in Russ.) DOI: 10.17516/1999-494X-2016-9-4-546-562
Khaliulin Ye.V., Kozlov A.V. [Machine for Bending of Titanium Alloy Pipes]. Nauka SUSU: Materialy 69-y nauchnoy konferentsii [Science in the South Ural State University: Materials of the 69th Scientific Conference.]. Chelyabinsk, South Ural St. Univ. Publ., 2017, pp. 545–549. (in Russ.)
Astashkin V., Shmatkov S., Shmatkov A. Polymer Composite Rational Application Field in the Gas-Escape Channel Construction of Industrial Chimneys and Ventilation Pipes. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016. рр. 1701–1708.
Chinyaev I.R., Fominykh A.V., Ilinykh E.A. The Valve is a Shutoff for the Passive Protection Systems of Pipelines. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 220–224.
Fomenko N.A., Aleksikov S.V., Artyomova S.G. High Pressure Piping of Tractive Transport Vehicles. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 1359–1362.
Gaponenko S.O., Kondratiev A.E., Zagretdinov A.R. Low-Frequency Vibro-Acoustic Method of Determination of the Location of the Hidden Canals and Pipelines. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 2321–2326.
Herrmann M., Fiderer M., Walters J. State-of-the-Art in Process Simulation of Forming Processes. Papers of the International Conference “New Developments in Forging Technology” in Fellbach (near Stuttgart). Frankfurt/M, MAT-INFO Werkstoff-Informationsgesellschaft, 2005. 68 p.
Korolev A.V., Korolev A.A. Microscip Mechanism in Raceways and Rolling Elements of Roller Bearings. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 497–501.
Kozlov A.V., Sherkunov V.G., Kyilcevich Ya.M. Stress State in Pipe on Flexure with Internal Shaping. Russian Engineering Reseach. New York, Allerton Press, Inc., 2009, vol. 29, no. 8, рp. 809–812.
Kozlov А.V., Khilkevich Y. The Technology and Equipment for Cold Bending of Pipes. The 29th International Conference on Mechanical Engineering: Book of Conference Lecturer. Haifa, Israel, Technion Publ., 2003. pp. 190–192.
Lopatin B.A., Khaziev T.R. Improved Design of Machine for Cold Cutting of Oil Pipes and Gas Pipelines. International Conference on Industrial Engineering, ICIE 2015. Chelyabinsk, Procedia Engineering, 2015, рр. 563–570.
LS-DYNA Theoretical Manual. Compiled By John O. Hallquist, 1998. 498 p.
Minatsevich S.P., Sharonov A.A., Borisov S.S. The Design of Safety Control Systems for Unattended Points of Technological Communication on Oil and Gas Pipelines. International Conference on Industrial Engineering, ICIE 2015. Chelyabinsk, Procedia Engineering, 2015, рр. 266–273.
Moskvicheva E.V., Sidyakin P.A., Shitov D.V. Method of Corrosion Prevention in Steel Pressure Pipelines in Sewerage Systems. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 2381–2386.
Plotnikov L.V., Zhilkin B.P., Brodov Yu.M. The Influence of Cross-profiling of Inlet and Exhaust Pipes on the Gas Exchange Processes in Piston Engines. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 111–116.
Sherkunov V., Korsakov A. The usage of 156 mm Diameter Continuous Cast Billets on “140” Pipe-Rolling Plant for Pipe Production. International Conference on Industrial Engineering, ICIE 2015. Chelyabinsk, Procedia Engineering, 2015, рр. 886–890.
Zakhezina A.M., Pryadko Y.G. Vibration Diagnostics of Gas Pipelines Technological Equipment Using Wavelet Analysis. International Conference on Industrial Engineering, ICIE 2016. Chelyabinsk, Procedia Engineering, 2016, рр. 300–306.
