Power unit with adjustable jet pump

Authors

  • E. К. Spiridonov South Ural State University, Chelyabinsk
  • G. G. Yakubov South Ural State University, Chelyabinsk

Keywords:

pump, ejector, power unit, regulation, throttle, nozzle, fluid, flow pressure, power, extreme characteristics, efficiency

Abstract

The article analyzes two ways changing the supply of the hydraulic power supply unit –
with the help of a throttle and jet pump with a variable nozzle outlet area. The unit with a jet pump, while maintaining the simplicity and high reliability of throttle control, is proved to be more efficient. Its application improves the operation of the main pump and increases the efficiency of the installation by more than 20 percent.

In a unit with a jet pump (ejector), high-pressure fluid is supplied to the nozzle via a branch from the discharge port of the main pump, and low-pressure fluid is supplied through the drain line of the hydraulic system. In the flow part of the jet pump there is an energy exchange between the flows. The total flow jet pump with a pressure He is fed to the suction side of the main pump. Changing the fluid supply unit power is carried out by regulating the flow area of the nozzle of the jet pump. When the nozzle is fully opened, the entire flow (or part of it) from the main pump returns through the ejector to its entrance, bypassing the hydraulic system. When closing the flow area of the nozzle, the entire flow of the main pump enters the hydraulic system. If the heads of the hydraulic power units with throttle and ejector versions are the same, then the required head of the main pump in the unit with an adjustable jet pump will be lower Consequently, the power to drive the pump will decrease. The authors analyze the work power units in dimensionless coordinates neglecting head losses in connecting lines. The feed main pump and its pressure serve as the source (basic) values.

Author Biographies

E. К. Spiridonov, South Ural State University, Chelyabinsk

доктор технических наук, профессор, заведующий кафедрой «Гидравлика и гидропневмосистемы»

G. G. Yakubov, South Ural State University, Chelyabinsk

аспирант кафедры «Гидравлика и гидропневмосистемы» идравлика и гидропневмосистемы»

References

Основы проектирования систем пневмо- и гидроавтоматики: монография / Ю.Л. Арзуманов, Е.М. Халатов, В.И. Чекмазов. – М.: Издат. дом «Спектр», 2017. – 459 c.

Гидравлика, гидромашины и гидроприводы: учеб. для машиностроит. вузов / Т.М. Башта, С.С. Руднев, Б.Б. Некрасов и др. – 5-е изд., стер., перепеч. со 2-го изд. 1982 г. – М.: Издат. дом «Альянс», 2011. – 423 с.

Никитин, О.Ф. Гидравлика и гидропневмопривод: учеб. пособие / О.Ф. Никитин. – 2-е изд., испр. и доп. – М.: Изд-во МГТУ им. Н.Э. Баумана, 2012. – 430 c.

Сравнительный анализ методик построения рабочих характеристик насосов с частотно-регулируемым электроприводом / А.А. Поспелов, В.Н. Виноградов, М.Ю. Зорин и др. // Вестник ИГЭУ. – 2007. – Вып. 2. – С. 1–8.

Калачев, В.В. Струйные насосы. Теория, расчет и проектирование / В.В. Калачев. – М.: Филинь: Омега-Л, 2017. – 418 с.

Соколов, Е.Я. Струйные аппараты / Е.Я. Соколов, Н.М. Зингер. – М.: Энергоатомиздат, 1989. – 352 с.

Meakhail, Tarek A. A Study of the Effect of Nozzle Spacing and Driving Pressure on the Water Jet Pump Performance/ Tarek A. Meakhail, Ibrahim R. Teaima // International Journal of Engineering Science and Innovative Technology. – 2013. – Vol. 2, no. 5. – P. 373–377.

Исследование характеристик кольцевых эжекторов и эжекторов с криволинейным входом / В.А. Сыченков, В.И. Панченко, Р.Р. Халиулин, Е.В. Сыченкова // Вестник КГТУ. – 2013. –

№ 2-2. – С. 56–59.

Li, Chuanjun. The principle and design of waste gas jet self – priming device / Chuanjun Li, Weidong Shi, Weidong Cao // Pump Technology. – 2006. – No. 1. – P. 3–4. DOI: 10.2991/ 15.2015.348

Rahman, Md. Mizanur Performance Evaluation of Water Jet Pump for Nozzle to Throat Area Ratios on Suction Lift / Md. Mizanur Rahman, Md. Assad-Uz-Zaman, Mohammad Mashud // International Journal of Mechanical & Mechatronics Engineering IJMME – IJENS, 2014. – P. 45–47.

Winoto, S.H. Efficiency of jet pumps / S.H. Winoto, H. Li, D.A. Shah // Journal of Hydraulic Engineering. – 2000. – Vol. 126 (2). – P. 150–156.

Темнов, В.К. Расчет и проектирование жидкостных эжекторов: учеб. пособие / В.К. Темнов, Е.К. Спиридонов. – Челябинск: ЧПИ, 1984. – 43 с.

Wang, Changbin. The determination method of jet pump best parameter / Changbin Wang // Fluid Machinery. – 2004. – Vol. 32 (9). – P. 21–25.

Liang, Aiguo Nunerical simulation and throat optimization / Aiguo Liang, Jingzhi Lin, Xinping Long // Pump Technology. – 2003. – Vol. 1. – P. 3–6.

Liu, Chunwang. Using venturi jet device to collect gas in the tank / Chunwang Liu, Xinpuan Liu, Lianjun Ma // Petroleum Machinery. – 2005. – Vol. 33 (2). – P. 64–65.

Aldaş, K. Investigation of Effects of Scale and Surface Roughness on Efficiency of Water Jet Pumps Using CFD / K. Aldaş, R. Yapıcı // Engineering Applications of Computational Fluid Mechanics. – 2014. – Vol. 8, no. 1. – P. 14–25. DOI: 10. 1080/ 19942060.11015494

Kong, Fanyu. Using jet device to eliminate cavitation vibration of large pump units / Fanyu Kong, Gang Chen, Jianrui Liu // Journal of China Safe Science. – 2005. – Vol. 15 (4). – P. 62–65.

Dong, Jianrui. Research of centrifugal pump jet self – priming device / Jianrui Dong, Weidong Shi, Zhongming Ye // Agricultural Engineering. – 2006. – Vol. 2 (1). – P. 89–92.

Ломакин, В.О. Влияние геометрической формы сопла струйного насоса на его характеристики / В.О. Ломакин, П.С. Чабурко // МГТУ им. Н.Э. Баумана. – 2014. – Т. 12. – С. 128–136. DOI: 10. 7463/0815.9328000

Long, X. Investigation on mechanism of critical cavitating flow in liquid jet pumps under ope-rating limits / X. Long, H. Yao, J. Zhao // International Journal of Heat and Mass Transfer. – 2009. –

Vol. 52. – P. 2415–2420

Downloads

Published

2019-10-09

Issue

Vol. 19 No. 3 (2019)

Section

Calculation and design