Numerical Simulations for Analyzing the Efficiency Parameters of a New Type of Flat-Plate Solar Collec-tors
DOI:
https://doi.org/10.14529/power200409Keywords:
flat-plate solar collector, heat capacity, ANSYS FLUENT 19.0, collector efficiencyAbstract
This article discusses a new design concept for a flat solar collector using flexible tubes. A flat-plate solar collector is designed to run cold water into solar heating systems instead of using expensive antifreeze fluids and to remove secondary media. The development of this type of solar thermal collectors will reduce the installation costs of traditional solar thermal systems without the need for secondary heat exchangers. We determined the main parameters of the heat capacity of a flat solar collector and computed the temperature profile of the absorber plate of a flat-plate solar collector with an inlet temperature of 30 °C. In contrast to a tube coil type temperature loop, it was found that the maximum temperature of the collector plate under the same inlet temperature conditions is much lower than that of the former. Using the CFD (Computational Fluid Dynamics) ANSYS FLUENT 19.0 commercial software package, a phase design was developed based on predictions of the reservoir thermal characteristics and the equivalent heat transfer coefficient of the absorber plates. Experimental test variables for a flat-plate solar collector were also calculated; these were higher with incident solar radiation than with ambient temperature.
References
Sint N.K.C., Choudhury I.A., Masjuki H.H., Aoyama H. Theoretical analysis to determine the efficiency of a CuO-water nanofluid based-flat plate solar collector for domestic solar water heating system in Myanmar. Solar Energy, 2017, vol. 155, pp. 608–619. DOI: 10.1016/j.solener.2017.06.055
Tian Z., Perers B., Furbo S., Fan J. Annual measured and simulated thermal performance analysis of a hy-b¬rid solar district heating plant with flat plate collectors and parabolic trough collectors in series. Applied Energy, 2017, vol. 205, pp. 417–427. DOI: 10.1016/j.apenergy.2017.07.139
Li Q., Chen Q., Zhang X. Performance analysis of a rooftop wind solar hybrid heat pump system for buil-dings. Energy Build, 2013, vol. 65, pp. 75–83. DOI: 10.1016/j.enbuild.2013.05.048
Tian Z., Zhang S., Deng J., Fan J., et al. Large-scale solar district heating plants in Danish smart thermal grid: Developments and recent trends. Energy Convers Manag, 2019, vol. 189, pp. 67–80. DOI: 10.1016/j.enconman.2019.03.071
Kalogirou S.A. Solar thermal collectors and applications. Progress in Energy and Combustion Science, 2004, vol. 30, pp. 231–295. DOI: 10.1016/j.pecs.2004.02.001
Cerón J.F., Pérez-García J., Solano J.P., García A., Herrero-Martín R. A coupled numerical model for tube-on-sheet flat-plate solar liquid collectors. Analysis and validation of the heat transfer mechanisms. Applied Ener-gy, 2015, vol. 140, pp. 275–287. DOI: 10.1016/j.apenergy.2014.11.069
Gunjo D.G., Mahanta P., Robi P.S. Exergy and energy analysis of a novel type solar collector under steady state condition: experimental and CFD analysis. Renew Energy, 2017, vol. 114, pp. 655–669. DOI: 10.1016/j.renene.2017.07.072
Álvarez A., Tarrío-Saavedra J., Zaragoza S., López-Beceiro J., Artiaga R., Naya S., et al. Numerical and experimental study of a corrugated thermal collector. Case Studies in Thermal Engineering, 2016, vol. 8, pp. 41–50. DOI: 10.1016/j.csite.2016.03.007
Del Col D., Padovan A., Bortolato M., Dai Prè M., Zambolin E. Thermal performance of flat plate solar col-lectors with sheet-and-tube and roll-bond absorbers. Energy, 2013, vol. 58, pp. 258–269. DOI: 10.1016/j.energy.2013.05.058
Chen G., Doroshenko A., Koltun P., Shestopalov K. Comparative field experimental investigations of dif-ferent flat plate solar collectors. Solar Energy, 2015, vol. 115, pp. 577–588. DOI: 10.1016/j.solener.2015.03.021
Facão J. Optimization of flow distribution in flat plate solar thermal collectors with riser and header
arrangements. Solar Energy, 2015, vol. 120, pp. 104–112. DOI: 10.1016/j.solener.2015.07.034
Fan J., Shah L.J., Furbo S. Flow distribution in a solar collector panel with horizontally inclined absorber strips. Solar Energy, 2007, vol. 81, pp. 1501–1511. DOI: 10.1016/j.solener.2007.02.001
Zhou F., Ji J., Yuan W., Cai J., Tang W., Modjinoua M. Numerical study and experimental validation on the optimization of the large size solar collector. Applied Thermal Engineering, 2018, vol. 133, pp. 8–20. DOI: 10.1016/j.applthermaleng.2018.01.026
Wang N., Zeng S., Zhou M., Wang S. Numerical study of flat plate solar collector with novel heat collect-ing components. International Communications in Heat and Mass Transfer, 2015, vol. 69, pp. 18–22. DOI: 10.1016/j.icheatmasstransfer.2015.10.012
Deng Y., Zhao Y., Wang W., et al. Experimental investigation of performance for the novel flat plate solar collector with micro-channel heat pipe array (MHPA-FPC). Applied Thermal Engineering, 2013, vol. 54, iss. 2,
pp. 440–449. DOI:10.1016/j.applthermaleng.2013.02.001
Deng Y., Wang W., Zhao Y., Yao L., Wang X. Experimental study of the performance for a novel kind of MHPA-FPC solar water heater. Applied Energy, 2013, vol. 112, pp. 719–726. DOI: 10.1016/j.apenergy.2013.06.019
Mansour M.K. Thermal analysis of novel minichannel-based solar flat-plate collector. Energy, 2013,
vol. 60, pp. 333–343. DOI: 10.1016/j.energy.2013.08.013
Moss R.W., Shire G.S.F., Henshall P., Eames P.C., Arya F., Hyde T. Design and fabrication of
a hydroformed absorber for an evacuated flat plate solar collector. Applied Thermal Engineerimg, 2018, vol. 138, pp. 456–464. DOI: 10.1016/j.applthermaleng.2018.04.033
Saedodin S., Zamzamian S.A.H., Eshagh Nimvari M., Wongwises S., Javaniyan Jouybari H. Performance evaluation of a flat-plate solar collector filled with porous metal foam: experimental and numerical analysis. En-ergy Conversion and Management, 2017, vol. 153, pp. 278–287. DOI: 10.1016/j.enconman.2017.09.072
Amirgaliyev Y., Kunelbayev M., Wójcik W., Amirgaliyev B., Kalizhanova A., Auelbekov O., Kataev N., Kozbakova A. Calculation and selection of flat-plate solar collector geometric parameters with thermosiphon cir-culation. Journal of Ecological Engineering, 2018, vol. 19, iss. 6, pp. 176–181. DOI: 10.12911/22998993/91882
Duffie J.A., Beckman W.A. Solar Engineering of Thermal Processes. 4th edition, New York, John Wiley & Sons, 2013. 944 p.
