Aligning the Loads of Horizontal-Roll Drives in a Platemill Stand
DOI:
https://doi.org/10.14529/power190212Keywords:
rolling mill, horizontal rolls, ski formation, electric drives, speeds, loads, coordination, systems, methods, method, regulator, structure, development, implementation, experimental studies, recommendationsAbstract
This paper overviews recent advancements in research into the emergence of frontal upward bends; it also covers papers on the distribution of load between the electric drives of upper and lower rolls in horizontal platemill stands. The bulk of research lacks appropriate emphasis on the alignment of these systems. The paper dwells structuring a speed regulator for Mill 5000, which is a platemill; the regulator runs load distribution and frontal upward bending algorithms. The paper substantiates the need to research their parameters for the purpose of better alignment. It presents oscillographs of upper- and lower-roll torques that prove the load is non-uniform in any roughing pass. The paper also analyzes the oscillographs of speeds and torques in a single pass. The existing speed configuration is shown to cause the lower-roll torque to reach its limits, whereas the upper-roll drive switches to the generator mode. The authors propose and validate a set of solutions to address these challenges. They herein present a load regulation method based on forced alignment of upper- and lower-roll drive speeds by disabling the integral part of the load distribution controller. An algorithm based on this method has been implemented in the APCS of Mill 5000; the resultant oscillographs prove better accuracy and shorter time to align the torques. It is herein recommended to apply the research results in the real-world setting.
References
Salganik V.M., Chikishev D.N., Pustovoytov D.O., Denisov S.V., Stekanov P.A. [Development of Modes of Asymmetric Plate Rolling of Low-Alloyed Steels in Order to Minimize the Defect of Sheet Bend-ing]. Metallurg [Metallurgist], 2013, no. 11, pp. 75–77. (in Russ.)
Chikishev D.N., Pozhidayeva E.B. [Analysis of the Reasons for the Vertical Bending of the Front End of the Strip during Hot Rolling Based on Mathematical Modeling]. Izvestiya vysshikh uchebnykh zavedeniy. Chernaya metallurgiya [Proceedings of Higher Educational Institutions. Ferrous Metallurgy], 2016, vol. 59, no. 1, pp. 204–208. (in Russ.)
Pesin A.M., Pustovoytov D.O., Sverdlik M.K. Razvitiye teorii i tekhnologii protsessa asimmetrichnoy tonkolistovoy prokatki kak metoda intensivnoy plasticheskoy deformatsii: monogr. [Development of the Theo-ry and Technology of Asymmetric Thin-Sheet Rolling as a Method of Severe Plastic Deformation: Mono-graph]. Magnitogorsk, G.I. Nosov Magnitogorsk State Technical University Publ., 2017. 150 p.
Kiefer T., Kugi A. An Analytical Approach for Modelling Asymmetrical Hot Rolling of Heavy Plates. Mathematical and Computer Modelling of Dynamical Systems, 2008, vol. 14, pp. 249–267. DOI: 10.1080/13873950701844915
Minton J.J., Cawthorn C.J., Brambley E.J. Asymptotican Alysis of Asymmetric Thin Sheet Rolling. In-ternational Journal of Mechanical Sciences, 2016, vol. 113, pp. 36–48. DOI: 10.1016/j.ijmecsci.2016.03.024
Philipp M., Schwenzfeier W., Fischer F.D., Wödlinger R., Fischer C. Front end Bending in Plate Roll-ing Influenced by Circumferential Speed Mismatch and Geometry. Journal of Materials Processing Technolo-gy, 2007, vol. 184, pp. 224–232. DOI: 10.1016/j.jmatprotec.2006.11.027
Varshavskiy E.A., Basurov V.M., Khrapov M.A. Sposob asimmetrichnoy prokatki perednikh kontsov tolstykh polos v kleti s individual’nym privodom valkov [The Method of Asymmetric Rolling of the Front Ends of Thick Strips in the Cage with an Individual Drive of the Rolls]. Patent RF, no. 2661523, 2018.
Shevchuk V.YA., Belichenko V.A., Orekhov N.G., Sivovolov Yu.I. Sposob lyzheobrazovaniya slitka na reversivnom stane goryachey prokatki s individual’nym privodom valkov i ustroystvo dlya ego osushchestvleniya [The Method of Ski Formation of the Ingot on the Reversing Hot Rolling Mill with an Indi-vidual Drive of
the Rolls and a Device for Its Implementation]. Patent USSR, no. 1759491, 1992.
Mugalimov R.G., Kharchenko G.N. Sposob reversivnoy prokatki [Reverse Rolling Method]. Patent USSR, no. 1741945, 1992.
Hiroshi Koyama, Keiji Saito. EP 0 130 551, B21B 37/00. Control Method and Apparatus for Rolling Mill. Date of publication of application 09.01.85. Bulletin 85/02.
Shokhin V.V., Permyakova O.V., Kisel’ E.S. [Study of the Electromechanical System of the Rolling Stand]. Elektrotekhnicheskiye sistemy i kompleksy [Electrotechnical Systems and Complexes], 2014, no. 2 (23),
pp. 40–43. (in Russ.)
Khramshin V.R., Andryushin I.Yu., Gostev A.N., Karandayev A.S. [Mathematical Model of Intercon-nec¬ted Electrical Systems of a Continuous Group of Broadband Mill]. Mashinostroyeniye: setevoy elektronnyy nauchnyy zhurnal [Mechanical Engineering: Network Electronic Scientific Journal], 2013, no. 1, pp. 12–21. DOI: 10.24892/rijie/20130102 (in Russ.)
Korotkov A.V., Kuz’min A.V., Tolochko O.I. Soglasovaniye skorostnykh rezhimov glavnykh privod-ov slyabinga 1150 [Coordination of Speeds of Main Slab Drives 1150]. Available at: http://masters.donntu.org/ publ2003/eltf/korotkov.pdf (accessed 01.05.2019).
Nesterenko D.L., Shevchenko D.V., Borovkov A.I. [Study of the Effect of the Difference in the Speeds of Rotation of the Rolls of One Stand on the Rolling Process]. Vestnik permskogo natsional’nogo is-sledovatel’skogo politekhnicheskogo universiteta. Mekhanika [Bulletin of the Perm National Research Poly-technic University. Mechanics], 2011, no. 1, pp. 72–79. (in Russ.)
Karandayev A.S., Khramshin V.R., Andryushin I.Yu., Golovin V.V., Shilyayev P.V. [Technological Schemes of Control of Electric Drives of the Finishing Group of a Wide-Strip Hot Rolling Mill]. Trudy VII kongressa prokatchikov. T.1 [Proceedings of the VII Congress of Distributors. Vol. 1]. Moscow, 2007, pp. 71–75. (in Russ.)
Karandayev A.S., Khramshin V.R., Andryushin I.Yu., Petryakov S.A., Khramshin R.R. [The Method
of Correction of the Thickness Variation of the Head Section of the Strip in the System of Automatic Control
of the Thickness of a Wide-Strip Hot Rolling Mill]. Elektrotekhnika [Electrical Engineering], 2013, no. 8,
pp. 34–38. (in Russ.)
Khramshin V.R., Karandaev A.S., Evdokimov S.A., Andryushin I.Yu., Shubin A.G., Gostev A.N.
Reduction of the Dynamic Loads in the Universal Stands of a Rolling Mill. Metallurgist, 2015, vol. 59, no. 3-4, pp. 315–323. DOI: 10.1007/s11015-015-0103-8
Galkin V.V., Karandayev A.S., Golovin V.V., Radionov A.A., Khramshin V.R., Gasiyarov V.R., Zalogin O.A. [Algorithm for Calculating the Speed and Load Modes of Electric Drives of Rolling Mill Stands during Rolling of Thick Lanes]. Izvestiya TulGU. Tekhnicheskiye nauki. Vyp. 3 [News TSU. Technical Sci-ence. Iss. 3], 2010, part 2, pp. 12–17. (in Russ.)
Shubin A.G., Loginov B.M., Gasiyarov V.R., Maklakova E.A. [Justification of Ways to Limit the Dyna¬mic Loads of the Electromechanical Systems of the Rolling Mill Stand]. Elektrotekhnicheskiye sistemy i kompleksy [Electrotechnical Systems and Complexes], 2018, no. 1 (38), pp. 14–25. DOI: 10.18503/2311-8318-2018-1(38)-14-25 (in Russ.)
Metel’kov V.P. [Evaluation of the Insulation Resource of the Stator Winding of an Induction Motor when Operating in Cyclic Modes]. Bulletin of South Ural State University. Ser. Power Engineering, 2013, vol. 13, no. 2, pp. 96–100. (in Russ.)
Zyuzev A.M., Metelkov V.P. Toward the Evaluation of the Thermal State of an Induction Motor in
the Recursive Short_Term Mode. Russian Electrical Engineering, 2014, vol. 85, no. 9, pp. 554–558. DOI: 10.3103/s1068371214090090
Medvedev V.N., Karandayev A.S., Karandayeva O.I., Mamleyeva Yu.I., Khramshina E.A. [Techno-logical Demand and Assessment of the Effectiveness of the Introduction of Variable Frequency Drives at the Thermal Power Plant]. Vestnik IG·EU, 2012, pp. 109–114. (in Russ.)
Karandayev A.S., Shemetova A.A., Karandayeva O.I., Shurygina G.V. [Calculation of the Reliability of Electric Drives in the Implementation of Frequency Converters]. Izvestiya vuzov. Elektromekhanika [News of Universities. Electromechanics], 2010, no. 1, pp. 59–64. (in Russ.)
Radionov A.A., Karandayev A.S., Khramshin R.R., Gubaydullin A.R., Karandayeva O.I., Khram¬shina E.A. [Evaluation of the Resource of Energy Saving in the Electric Drive of a Blower Fan with a Two-Speed Asynchronous Electric Motor]. Bulletin of South Ural State University. Ser. Power Engineering, 2014, vol. 14,
no. 3, pp. 61–70. (in Russ.)
Shemetova A.A., Karandayev A.S., Karandayeva O.I. [The Method of Calculating the Reliability of
Automated Electric Rolling mill]. Izvestiya vuzov. Elektromekhanika [News of Universities. Electromechan-ics], 2009, no. 1, pp. 48–54. (in Russ.)
